An Experimental Study on Hole Quality and Different Delamination Approaches in the Drilling of CARALL, a New FML Composite

Basit Öğe Kaydı
dc.authorid0000-0002-5217-872Xen_US
dc.authorid0000-0002-9129-8935en_US
dc.authorscopusid36482674300en_US
dc.authorscopusid6507857056en_US
dc.authorwosid-en_US
dc.authorwosidG-5458-2017en_US
dc.contributor.authorEkici, Ergün
dc.contributor.authorMotorcu, Ali Rıza
dc.contributor.authorYıldırım, Ensar
dc.date.accessioned2023-06-12T10:55:44Z
dc.date.available2023-06-12T10:55:44Z
dc.date.issued2021en_US
dc.departmentFakülteler, Mühendislik Fakültesi, Endüstri Mühendisliği Bölümü
dc.description.abstractIn this study, the hole quality was investigated in the drilling of CARALL composite. In addition, the delamination factor calculation approaches of Chen, Davim, and Machado were compared in terms of the delamination damage at the hole entrance surface. Chen's approach is based on the conventional delamination factor (Fd) and Davim's on the adjusted delamination factor (Fda). Finally, Machado's approach is based on the minimum delamination factor (Fmin). The values closest to the nominal hole diameter value were obtained with the uncoated (T1), followed by the TiN-TiAlN-coated (T2) and TiAl/TiAlSiMoCr-coated (T3) carbide drills, respectively. The average circularity error values for the hole top and bottom surfaces were 6.184 µm, 7.647 µm, and 8.959 µm for T1, T2, and T3 tools, respectively. Delamination factor values varied between 1.174 and 1.804. The Fda values were found to be the highest, followed by Fd values, with Fdmin values determined as the lowesten_US
dc.identifier.citationEkici, E., Motorcu, A. R., & Yıldırım, E. (2021). An experimental study on hole quality and different delamination approaches in the drilling of CARALL, a new FML composite. FME Transactions, 49(4), 950-961. doi:10.5937/FME2104950Een_US
dc.identifier.doi10.5937/FME2104950E
dc.identifier.endpage961en_US
dc.identifier.issn1451-2092
dc.identifier.issn2406-128X
dc.identifier.issue4en_US
dc.identifier.scopus2-s2.0-85121795115
dc.identifier.startpage950en_US
dc.identifier.urihttps://doi.org/10.5937/FME2104950E
dc.identifier.urihttps://hdl.handle.net/20.500.12428/4276
dc.identifier.volume49en_US
dc.identifier.wosWOS:000734088700020
dc.identifier.wosqualityN/A
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.institutionauthorEkici, Ergün
dc.institutionauthorMotorcu, Ali Rıza
dc.language.isoen
dc.publisherBelgrade Universityen_US
dc.relation.ispartofFME Transactionsen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectCarbon reinforced aluminum laminate (carall)en_US
dc.subjectCircularity erroren_US
dc.subjectDelamination factoren_US
dc.subjectDimensional accuracyen_US
dc.subjectFiber metal laminate (fml)en_US
dc.titleAn Experimental Study on Hole Quality and Different Delamination Approaches in the Drilling of CARALL, a New FML Composite
dc.typeArticle

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
Ergun_Ekici_Makale.pdf
Boyut:
1.3 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Araştırma Makalesi
İndir
Lisans paketi
Listeleniyor 1 - 1 / 1
[ X ]
İsim:
license.txt
Boyut:
1.44 KB
Biçim:
Item-specific license agreed upon to submission
Açıklama:
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Endüstri Mühendisliği Bölümü Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu