Yazar "Yazar, Mehmet" seçeneğine göre listele
Listeleniyor 1 - 8 / 8
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Comparative efficiency and performance analysis of spur gear and non-circular (square) gear hydraulic pumps(Elsevier Ltd, 2025) Yazar, MehmetThis study addresses the comparative energy consumption performance of hydraulic spur gear pumps, whose technical features and efficiency are well-known, and non-circular (square) gear pumps, whose technical features and efficiency have not been sufficiently investigated, under the same operating conditions. The study encompasses both theoretical and experimental analyses. In the theoretical section, the design process of the square gear pump, the creation of gear geometry, its operating principles, and potential advantages are explained in detail. At this stage, physical prototypes were developed using CAD models and rapid manufacturing techniques, and their functionality was verified. Thus, the volumetric flow rate, operating pressure, hydraulic oil temperature variations, and power consumption at different speeds of the gear pumps were experimentally analyzed and evaluated in detail. The findings indicate that, at the same speed and within the same time unit, the square gear pump consumed approximately 0.59 %–33.94 % less power (kW) per unit flow rate and 8.08 %–74.33 % less power per unit pressure compared to the spur gear pump. These results reveal that the square gear pump consumes less power than the spur gear pump. Furthermore, the square gear pump demonstrated higher fluid transport capacity and operating pressure during operation. These results indicate that the square gear pump offers a promising alternative for industrial applications, combining high efficiency with low power consumption. © 2025 Elsevier LtdÖğe Computational fluid dynamics analysis of flowmeters with elliptical gear pairs and evaluation of calculated flow rate by Taguchi method(Elsevier Sci Ltd, 2023) Pazarkaya, Ibrahim; Yazar, Mehmet; Ozdemir, AhmetAccurate determination of flowmeters' design and manufacturing parameters ensures that commercially available flowmeters' declared characteristics are reliable. In this study, nine different flow meters with elliptical gear pairs were manufactured at three different a/b ratios, three different modules, and three different tooth numbers, and the Computational Fluid Dynamics (CFD) models were prepared. CFD analysis forms the basis of the study's methodology, which seeks to statistically identify the most appropriate elliptical gear parameters according to the flow meters manufactured and what the most influential parameter that changes the measured flow rate is. As the pressure of the fluid increased, the measured and CFD-calculated flow rates decreased. According to the measured flow rates and CFD analysis results, it was found that the average flow rate change was -0.0102 %, the biggest change was in the flow meter coded Db-03 with 0.0855 % at 3.00 MPa pressure, and the least change was in the flow meter coded Db-02 with 0.0002 % at 4.50 MPa pressure. The CFD models developed for the manufactured flowmeters were suitable for all flowmeters according to the measured and calculated percent flow rate variations. Taguchi L9 analysis revealed that a/b = 1.40, m = 2.50 mm, and z = 40 teeth are the optimal manufacturing parameters for elliptical gear, according to the signal-to-noise ratio based on the largest, best analysis. According to the analysis of variance, the modulus value contributed the most to the calculated flow rate at 65.25%, whereas the a/b ratio contributed the least with 0.96%.Öğe Design, Manufacturing and Operational Analysis of Elliptical Gears(Springer, 2021) Yazar, MehmetIn this study, the polar equations and complex numbers of curves are used to design elliptical gears that require machine tools that are difcult to produce by conventional methods and require special consultation. Using these equations, a package program has been developed by using AtuoLISP programming language in order to realize the desired number of teeth and design of elliptical gears in AutoCAD environment.ss With this package program, elliptical gear design has been realized in 5 diferent modules and number of teeth and they have been manufactured in CNC Wire EMD. The most important parameter for analyzing the workability of elliptical gears is the distance changes between axes. In order to analyze this experimentally, an elliptical gear analysis mechanism is designed and manufactured. In this study, a pair of elliptical gear driven crank connecting bar mechanism and four bar mechanism were analyzed. In addition, the distribution of tooth stress using the Cosmosworks module of the Solidworks program and frequency analysis using the ANSYS program were performed. The results of this study exhibitioned that elliptical gears can be used in many industrial applications.Öğe Effect of lapping process on axis misalignment and surface roughness in elliptical gear pairs(Elsevier Sci Ltd, 2024) Pazarkaya, Ibrahim; Yazar, Mehmet; Karabulut, Sener; Uzun, Gultekin; Ozdemir, AhmetThis study aims to investigate the effect of application of the lapping process on the amount of axis misalignment in elliptical spur gears. Using a Taguchi L9 experimental design, nine distinct pairs of elliptical spur gears were manufactured, each featuring three distinct modules (m), number of teeth (z), and ratio of major and minor radius of the pitch ellipse (a/b). Specialized hardware and software were developed to determine inter-axis misalignment in the gear pairs. The hardware measured the misalignment, while the software collected data from a digital indicator, recording changes in inter-axis alignment at different angular positions of the gear pairs. Three diverse parameters were utilized in the lapping processes: rotational speed of 120 rpm, 170 rpm, and 220 rpm; duration of 10 min, 20 min, and 30 min; and mass of 0.5 kg, 1 kg, and 1.5 kg. Axial misalignment of the gear pairs was evaluated both before and after the lapping process. The most significant change in misalignment was observed at 76 mm for gear pairs with parameters m = 2.0, z = 25, a/b = 1.60, while the smallest misalignment change was recorded at 5 mm for gear pairs with parameters a/b = 1.60, m = 1.60, z = 40. After lapping process, the average surface roughness values of all gear pairs improved by an average of 27.64%, and no significant weight loss was noted. The optimal lapping parameters were determined based on post-lapping average surface roughness values, and they were found to be 220 rpm, 10 min, and a 1 kg weight. Although the rotational speed and duration varied, it was observed that a constant 1 kg weight parameter was the optimal lapping weight for all gear modules.Öğe Eliptik Dişli Çarkların Bilgisayar Destekli Doğal Frekans ve Mod Analizi(2021) Yazar, MehmetDairesel olmayan dişli çarkların önemli bir üyesi olan eliptik dişli çarkların tasarım denklemleri çalışmanın ilk aşamasında hazırlanmıştır. İkinci aşamasında hazırlanan denklemleri döngü içerisinde çözmek ve istenilen diş sayısı ve modülde eliptik dişli çarkın 2-D modellenmesi için AutoLISP programlama dili ile bilgisayar ortamında mini bir paket program yazılımı geliştirilmiştir. Geliştirilen paket program ile AutoCAD ortamında modülü 2, diş sayısı 32 olan eliptik dişli çarkın tasarımı yapılmıştır. Tasarımı yapılan eliptik dişli çarkın sonlu elemanlar yöntemiyle doğal frekans ve modlarını belirlemek için ANSYS programı kullanılmıştır. Eliptik dişli çarkın tam 3-D modelini oluşturmak için ABAQUS yazılımı kullanılmıştır. Eliptik dişli çarkın doğal titreşim özelliği, titreşim türleri ve doğal frekansları tespit edilmiştir. Bu yazılım eliptik dişli çarkların mühendislik uygulamaları ve dinamik analizleri için kullanılabilir. Bir eliptik dişli çarkın titreşim özelliğini belirlemek için her türlü dinamik yüklere nasıl yanıt verdiğini belirlemek ve herhangi bir tasarım veya uygulama yapmadan önce daha pratik ve düşük maliyetli bir analiz yapmak için bu yöntem kullanılabilir. Yapılan analizler sonucunda tam durmayı gerektirmeksizin düzensiz hareketin elde edilebildiği bir makine elemanı olarak eliptik dişli çarkların kullanılabileceği tespit edilmiştir.Öğe Eliptik Dişli Tasarımı, İmalatı, Analizi ve Eliptik Dişli Esaslı Endüstriyel Uygulamalar(2022) Pazarkaya, Ibrahım; Yazar, Mehmet; Özdemir, AhmetEliptik dişliler, bir elips üzerine eşit adımlarla diş profillerinin dizildiği ve tahrik edilen mil hızının aynı dönüş içerisinde değiştirilmesi istenen durumlarda kullanılan özel bir dişli türdür. Eliptik dişliler üzerine yapılan çalışmaların diş profillerinin tasarımı üzerine yoğunlaştığı ve prototip imalatlarına yönelik araştırmaların arttığı görülmektedir. Eliptik dişlilerin diş profillerinin silindirik dişliler gibi özdeş olmayacağından hareketle geliştirilen eliptik dişlinin diş profili; kramayer veya silindirik düz dişli formlu kesicinin bölüm elipsi üzerinde yuvarlanma yöntemine uygun olarak evolvent eğriye sahip diş yanaklarının şekillendirilmesiyle elde edilmektedir. Eliptik dişlilerin imalatında CNC tel erozyon tezgahlarından faydalanmanın yaygınlaştığı, bununla birlikte azdırma tezgâhları için elektronik dişli kutuları geliştirilerek eliptik dişlilerin standart modülde imalatının da mümkün olduğu tespit edilmiştir. Eliptik dişli çiftleri farklı makine ve teçhizatta kullanılmakta, özellikle eliptik dişli çiftine sahip debimetre ve pompaların yaygınlaştığı görülmektedir. Enerji verimliliğinin son derece önem kazandığı günümüzde, yüksek miktardaki akışkanların debilerinin doğru ve hassas ölçülmesi, aynı zamanda akışkan transferindeki kayıpların da giderilmesi de gerekmektedir. Bu derleme çalışmasında eliptik dişlilerin tasarımı, geleneksel ve geleneksel olmayan imal usulleri ile imalatı, dayanım ve titreşim analizleri ve literatürde yer alan muhtelif endüstriyel uygulamaları gözen geçirilmiş ve çalışmanın ortak bulguları elde edilmiştir. Eliptik dişlilerin yakın gelecekte bünyesinde mekanik kısım barındıran birçok akıllı ürünün vazgeçilmez bir organı olacağı öngörülmektedir.Öğe Giyilebilir Hareket Sensörü Kullanılarak Dinamik Model ile Üst Uzuv Eklemleri Üzerine Etkiyen Kuvvetlerin ve Torkların Belirlenmesi(2020) Yanıkören, Mithat; Yılmaz, Sezcan; Usanmaz, Bilal; Tezgel, Selim; Yazar, Mehmet; Gündoğdu, ÖmerBu çalışmada günlük hayatta en sık kullanılan vücut bölümlerinin başında gelen üst uzuvlara ait omuz vedirsek eklemlerindeki kuvvet ve tork değerlerinin belirlenmesi amaçlanmıştır. Denekten dik konumda ikenmasada duran belirli bir yükü alması kendisine yaklaştırması ve geri bırakması istenmiştir. Deneğin bu göreviyerine getirirken gerçekleştirdiği hareketler esnasında omuz ve dirseğinde meydana gelen eklem kuvvet vetorklarının belirlenebilmesi için Newton-Euler metodu kullanılarak dinamik bir model oluşturulmuştur. Eklemlereait konum verilerinin ölçülmesinde giyilebilir hareket sensörleri kullanılmıştır. Bu sensörlerden alınan hareketverileri ile oluşturulan dinamik model kullanılarak eklemlerdeki tork ve bağ kuvveti değerleri hesaplanmıştır.Elde edilen hesaplama sonuçları karşılaştırmalı olarak değerlendirilerek eklem kuvvet ve torklarının hangidurumlarda arttığı ve ne gibi tedbirlerle azaltılabileceği ortaya konulmuştur.Öğe Spur gear design, manufacturing and noise analysis according to rolling method using complex numbers(2022) Yazar, Mehmet; Yanıkören, MithatIn this study, a software has been improved for parametric drawing and modeling of spur gear using complex numbers in the CAD setting. AutoLISP programming language was used in software development. In the system, parameters such as module and number of teeth can be entered by the user and drawing or modeling of the gears in the CAD environment can be done automatically. This study provides the designer with fast and functional and more precise utility alternative for gear drawing and modeling. In addition, within the scope of the study, the same number of teeth and at the module spur gear were designed in the AutoCAD package program with the classical method. Spur gears, designed in AutoCAD program with the developed package program and classical method, were produced on the wire EDM machine by deriving cutting codes in the MasterCAM program. Noise analysis of the produced spur gear pairs has been made. It was determined that the spur gear pair, designed and produced with the package program developed within the scope of the study, operates approximately 8 dB less noise than the spur gear designed and produced with the classical method. It is possible to design and manufacture the gear in the desired profile by changing the cutter profile for non-standard thread shapes to provide the performance required for a tool and standard tool parameters. For further investigations, spur gears produced by round-ended cutters can be applied symmetrically and asymmetrically.